Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
anycubic_kossel_plus [2017/05/14 15:56] sschueller |
anycubic_kossel_plus [2017/06/23 12:31] (current) sschueller |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Anycubic Kossel Plus ====== | ====== Anycubic Kossel Plus ====== | ||
| - | ===== BL / 3D Touch Setup ===== | + | * [[BL Touch]] |
| - | ==== Hardware ==== | + | * [[Inductive Probe]] |
| - | - Print bracket such as: http://www.thingiverse.com/thing:2251115 | + | |
| - | - Connect White/Black wire to z-min-endstop (S = (signal - white), - = (minus - black)). Orientation doesn't matter | + | |
| - | - Connect Brown/Red/Orange wire to servo 0 port (S = Orange, + = Red, - = Brown) NOTE: on the Tri Gorila Board + and - are reversed. | + | |
| - | {{::20170513_152037.jpg?direct&300|}}{{::20170513_164053.jpg?direct&300|}} | + | |
| - | + | ||
| - | - Powering on system should make LED light red and move the pin a few times | + | |
| - | + | ||
| - | + | ||
| - | ==== Software (Marlin) ==== | + | |
| - | + | ||
| - | Using release from Anycubic: https://drive.google.com/drive/u/0/folders/0B8VIB533cgdMa1czMW5hNWlXYW8 | + | |
| - | Some of these may already be set. | + | |
| - | + | ||
| - | <code Configureation.h> | + | |
| - | #define MOTHERBOARD 43 // using 33 doesn't work | + | |
| - | + | ||
| - | #define BLTOUCH // turn on probe | + | |
| - | + | ||
| - | // these values strongly depend on your mount! | + | |
| - | #define X_PROBE_OFFSET_FROM_EXTRUDER 36.1 // X offset: -left +right [of the nozzle] | + | |
| - | #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] | + | |
| - | #define Z_PROBE_OFFSET_FROM_EXTRUDER -3.6 // Z offset: -below +above [the nozzle] | + | |
| - | + | ||
| - | #define XY_PROBE_SPEED 6000 | + | |
| - | + | ||
| - | #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN | + | |
| - | + | ||
| - | #define Z_CLEARANCE_DEPLOY_PROBE 50 // Z Clearance for Deploy/Stow | + | |
| - | #define Z_CLEARANCE_BETWEEN_PROBES 10 // Z Clearance between probe points | + | |
| - | + | ||
| - | #define AUTO_BED_LEVELING_BILINEAR | + | |
| - | + | ||
| - | // works better but still not ideal | + | |
| - | #define SAFETY_MARGIN 5 | + | |
| - | #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - sqrt(sq(X_PROBE_OFFSET_FROM_EXTRUDER)+sq(Y_PROBE_OFFSET_FROM_EXTRUDER)) - SAFETY_MARGIN ) | + | |
| - | // #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS -10) | + | |
| - | #define LEFT_PROBE_BED_POSITION -(DELTA_PROBEABLE_RADIUS) | + | |
| - | #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS | + | |
| - | #define FRONT_PROBE_BED_POSITION -(DELTA_PROBEABLE_RADIUS) | + | |
| - | #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS | + | |
| - | + | ||
| - | </code> | + | |